1.按圖紙要求做好地坑、預埋件與地坑地面平齊，地坑圖廠家會根據每個產品的不同設計不同的圖紙給客戶。 Well, the pit pit ground and embedded parts according to the requirements of the drawings, figure pit manufacturer will according to the different design of each product drawings to different customers.

2.調整成都升降平臺上行程：將平臺升起，升到指定位置，確認完好，安裝限位開關。Adjust the trip on the Chengdu landing platform: the platform rises, or to the designated location, to be confirmed in good condition, the installation of the limit switch.

3.將成都升降機導軌輪輪焊接于平臺兩側（四個角的內側）。再將導軌（槽鋼）垂直于平臺兩側的導軌輪位置，將導軌輪（按照導軌輪照片上的方法）放置于導軌內，使導軌輪在導軌內可以滑動自如。Welding the Chengdu elevator guide rail wheel on both sides of the platform (inside the four corners). Then the guide rail is perpendicular to the guide rail wheel on both sides of the platform, and the guide rail wheel (according to the method of the guide rail wheel) is placed in the guide rail, so that the guide rail can slide freely in the guide rail.

4.接好電源，啟動成都升降平臺設備，檢查導軌與主機配合是否完好。Connect the power supply, start the Chengdu lifting platform equipment, check the guide rail and the host is in good condition.

5.尋找專業電工安裝控制箱，把線路整理好，按照成都升降平臺廠家的指導連接好線路。 Find a professional electrician to install the control box, the line finishing good, in accordance with the guidance of the Chengdu elevator manufacturers to connect a good line.

6.用膨脹螺絲將鐵板(鐵板大小能放開導軌就可)固定在放置導軌的底部位置，然后將導軌焊接在鐵板上，同時將頂部連接，使其上下固定牢固。將貨梯臺面放置于地坑內，將平臺調整到臺面與地面水平處，將平臺底部與預埋件焊接牢固。With the iron (iron size expansion screws can open can guide) is fixed at the bottom position of the guide rail, and the rail welding in the plate, while the top connection, the upper and lower fixed firmly. The elevator table into the pit, will be adjusted to the table and the ground level of the platform, the platform bottom and embedded parts welded firmly.

7.試機：成都升降機升降過程中，導軌輪須在導軌內平穩滑動，使平臺升降平穩。Test machine: Chengdu lift in the course of the lift, the guide rail in the guide rail in a smooth slide, so that stable platform.

8.成都升降機驗收：試機完畢后，清理好現場，排除其他雜物，以備投入使用。Chengdu elevator acceptance: after the test machine is completed, clean up the scene, excluding other debris, in order to prepare for the use of.